DS

This infrared alarm barrier can be used to detect persons passing through doorways, corridors and small gates. The transmitter emits a beam of infrared light which is invisible to the human eye. The buzzer at the output of the receiver is activated when the light beam is interrupted by a person passing through it. Infrared Light Alarm Transmitter Circuit Schematic Infrared Alarm Barrier Receiver Circuit Schematic How to make an infrared barrier alarm The transmitter and receiver circuits of the infrared alarm system shown here have been designed for a range of several meters, almost independent of ambient light conditions. Only in the rare case of the receiver sensor being exposed to bright, direct sunlight, some screening measures have to be added. The transmitter does not emit a continuous infrared signal, Rather, it is modulated, that is, the 36-kHz carrier used to pulse the IRED (infrared emitting diode) on and off is itself switched on an off at a rate of about 300 Hz. The reason...

This is Infrared Remote control transmitter circuit has high performance and can be applied to works with the various infrared receiver circuit. To made easily. And best to save your money. I need not tell you much, what is the infra red remote control. Because you have known as well. so I recommend circuits 2 types, as appropriate. - The first is simple circuits. Infrared light from a set to a set to work immediately. - Then another circuits, is designed to have wider applications. Can be set program that will be must have a beam of infrared light to circuits few times to work. Which both need to have the good Infrared Remote control circuit, before. The infrared remote control transmitter circuit. Usually, when input voltage to the infrared diode. Will be have the beam infrared light which can be seen with the naked eye out -But in real applications. We need to enter the signal pulse with a frequency of about 5kHz, to the infrared diode, for eliminate the various interference. And re...

What is PIR ? Passive Infrared Sensor Circuit Diagram . Detectors or pyroelectric sensors, passive infrared or PIR sensor, are made of a crystalline material that generates an electric charge on the surface when exposed to heat in the form of infrared radiation. When radiation increases the amount of electrical charge increases too and this load is measured with a sensitive FET transistor which is inside the sensor module. With the RIP is commonly used as a motion detector of an object by detecting the infrared signal radiated from the object (people and animals). The Passive Infrared Sensors are also used in remote thermometers. Pinning PIR sensor Pin 1 of the PIR must be connected to the positive supply 5V DC. Pin 2 is the output of PIR sensor, it must have a connection to the earth through a resistor of 47K to 100K (depending on the circuit). Pin 3 of the RIP must be connected to ground or negative circuit. Simple Circuit Diagram using PIR Sensor Simple circuit motion sensor PIR det...

Description  Most homes today have at least a few infrared remote controls, whether they be for the television, the video recorder, the stereo, etc. Despite that fact, who among us has not cursed the light that remained lit after we just sat down in a comfortable chair to watch a good film? This project proposes to solve that problem thanks to its original approach. In fact, it is for a common on/off switch for infrared remote controls, but what differentiates it from the commercial products is the fact that it is capable of working with any remote control. Therefore, the first one you find allows you to turn off the light and enjoy your movie in the best possible conditions. The infrared receiver part of our project is entrusted to an integrated receiver (Sony SBX 1620-52) which has the advantage of costing less than the components required to make the same function. After being inverted by T1, the pulses delivered by this receiver trigger IC2a, which is nothing other than a D fli...

This ultra-simple remote control extender is ideal for use with a hidden video recorder. The recorder is a Panasonic NV-SD200 and is used as part of a camera surveillance system. A PICAXE-08-based circuit is used to detect events and control the recorder. It also flashes a LED near the monitor to indicate the number of events since last viewing. Strangely, the NV-SD200 model refused to work with a number of commercial infrared remote control extenders, hence the need for this design. As a bonus, it uses less power than a traditional extender (no plugpacks) and the remote can still be used in the normal manner. As shown, an additional 5mm infrared LED is mounted directly in front of the equipment to be controlled. This is cabled back to a convenient location near the monitor and terminated in a 3.5mm plug. To modify the remote control unit, break the circuit to the anode of the existing infrared LED and wire in a 3.5mm headphone socket. In most cases, the LED will be accessible ...