DS

autho r: Santa Cruz (Nickname - Bob) - Zagreb, Croatia Regulated DC power supply, short circuit safe, and with current limiter This PSU has been especially designed for current-hungry ham radio transceivers. It delivers safely around 20Amps at 13.8V. For lower currents, a separate current limiting output, capable of 15ma up to a total of 20A has been added. Let us see what we have got here. The power transformer should be capable to deliver at least 25A at 17.5 to 20V. The lower the voltage, the lower power dissipation. The rectified current will be “ironed” by the C1, whose capacity should not be less than 40.000uF, (a golden rule of around 2000uF/A), but we recommend up to 50.000uF. This capacity can be built up by several smaller capacitors in parallel. The base of this design is a simple 12V regulator (7812). The output voltage can be brought to desired value (here 13.8V) by two external resistors (R5 and R6) using this formula: U= 12(1+R5/R6) The low currents (here 15mA...

This amplifier circuit is very cheap, because not a lot of components that are required, and the voltage or amperage required is also not too large, so the transformer or power supply is also quite cheap. IC which can be used in power amplifier circuit is the KA2201, LM820M, TBA820M, U820. This amplifier output of 2 W and 4 ohm impedance, which can be applied to the speaker with 4W power, on such small speakers in front of a PC. For the required minimum input voltage of 3 volts and a maximum of 16 volts, for the recommended voltage of 12 volts. Parts Resistor R1 = 100K R2 = 120R R3 = 100R R4 = 10R Capacitor C1 = 0.1uF C2 = 100uF C3 = 47uF C4 = 100uF C5 = 470uF C6 = 220pF C7 = 100nF IC U1 = KA2201 , LM820M, TBA820M, U820

This is Low power amplifier , based on IC TDA2824 product of Philips. Maximum output is about 2 X 1,8 Watt , these include low  output amplifier type. Minimum required voltage 3 Volts and maximum voltage of 18 volts DC. Specification : Supply Voltage : 3 - 18 Volts Power Output   : 2 x 1,3 Watts RL impedance  : 4 Ohms Frequency responses : 30Hz -18kHz Quiescent current : 6 mA                

Here I will explain about the necessary voltage and power amplifier output. The voltage should have at least approximately 9Volt 30Volt voltage and maximum voltage on the DC current. For maximum output of 2 X 2Watt with impedance 8-16 ohm. Because this amplifier circuit using ic and ic is used have the equation, so that if used different ic, then the required output voltage and also differ depending ic respectively. Part List : Resistor R1 = 1M R2 = 1M R3 = 1K R4 = 1K R5 = 100K R6 = 100K R7 = 1R R8 = 1R Capacitor C1 = 1uF C2 = 220uF C3 = 1uF C4 = 100uF C5 = 5uF C6 = 5uF C7 = 0.1uF C8 = 220uF C9 = 220uF C10 = 0.1uF IC U1 = ULN2274B , ULN2277 , ULN2278B

  3000 watt power inverter 12V DC  to  230V AC Circuit Diagram of 3000 watt power inverter 12V DC  to  230V AC Fig. 2: Sine-wave voltage and conventional square wave voltage with both 230 Volt rms Fig. 3: Square wave voltage with duty cycle 25% for 230 Volt rms ("modified sine") PCB Layout: 3000 watt power inverter 12V DC  to  230V AC   Component Placement: 3000 watt power inverter 12V DC  to  230V AC fig.: output voltage with no load or inductive load. fig.: resistor 0,001 Ohm made of high-grade steel sheet metal Control electronics | 3000 watt power inverter 12V DC  to  230V AC fig.: control electronics on strip hole plate (previous version) and PCB of the "professional edition" Assembly of the mosfet-transistors on the heat sink | 3000 watt power inverter 12V   DC  to  230V AC fig.: heat sink, mosfet transistors, connections. Final assembly | 3000 watt power inverter 12V DC  to  230V AC fig.: 15...

Here this circuit diagram is for +12V regulated (fixed voltage) DC power supply. These power supply circuit diagram is ideal for an average current requirement of  1Amp. This  circuit is based on IC LM7812. It is a 3-terminal (+ve) voltage regulator IC. It has short circuit  protection , thermal overload protection.  LM7812 IC is from LM78XX series. The LM78XX series IC is  positive voltage regulator IC for different voltage requirements, for example LM7805 IC is made for 5 volt fixed output voltage . There is LM79XX IC series for negative voltage . Circuit diagram of 12V fixed voltage power supply   A transformer(Tx=Primary 230 Volt, Secondary 12 Volt , 1Amp step down transformer) is used to covert 230V to 12V from mains. Here used a bridge rectifier made by four  1N4007 or 1N4003 diode to convert AC to DC . The filtering capacitor 1000uF,25V is used to reduce the ripple and  get a smooth DC voltage. This circuit is very easy to build. For good p...

The HA13155 is four-channel BTL amplifier IC designed for car audio, featuring high output and low distortion, and applicable to digital audio equipment. It provides 33 W output per channel, with a 13.7 V power supply and at Max distortion. Circuit diagram: Datasheet for HA13155: Download

3V / 35mW dual power amplifier